I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I am using nRF SDK 16,0 and ble_app_template for pca10040 with Softdevice 132.
The example works fine, on my DK board but I need to utilize timers for my application.
...
Hi everyone,
I found that I can log the CPU persantage usage here . I have enabled the NRF_PWR_MGMT_CONFIG_CPU_USAGE_MONITOR_ENABLED but I do not know what steps I have...
I am working with a proximity beacon example. In that runs scanning and advertisement code, And in testing, most of the cases, I am not able to get the Advertisement packet...
hello ,
I would like to know what is the use of m_in_boot_mode global variable in BLE mouse example, m_in_boot_mode updates it value in a handler called on_hids_evt, so...
Hello,
I'm trying to program the Makerdiary nRF52840-MDK USB Dongle with the Bluetooth sample project central_uart but when I load the built HEX file to Programmer file...
I'm on my Windows 10 machine using Segger Embedded Studio V4.52C. I'm using SDK16 and Mesh 4.0.1 with FreeRTOS. I have built the light switch server example found here to...
Hello,
I am using SDK v1.3.0 with modem firmware v1.2.0 with the nRF9160 DK v0.9.0. I am using an AT&T SIM card to connect to their LTE Cat-M1 network.
I would like to...
I’ve not yet been able to successfully get an application (in this case Blinky) to complete a BLE DFU load and then execute. I’ve tried all the suggestions I’ve found in the...
Hello,
I would like to learn a little more about the possibilities of thin planning of connection events. I rely on chapter 15, in particular on part 15.7 of the S140 SoftDevice...
Hi, I'm trying to do the iot mqtt publisher example with the nRF5_SDK_15.3.0_59ac345, a nrf52840 and a Raspberry Pi 3 B+ as a gateway but I got some problems :
After the...
We have been testing the DK board and Thingy:91 and had a few questions on enabling PSM/queued mode.
We are able to enable queued mode for the lwm2m_client example on the...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi!
I'm going over the nRF52820 chipset, and I'm not sure I completely understand the reference schematics in regards to the LC filters on the REG1 DCDC enabled option....
