I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
As far as I can tell, the packet sent by nRF24L01+ PTX only contains a destination address. There if no information that identifies the transmitter (i.e. PTX).
So, when...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
As regards the NRF52840, I want to make sure that it is in System Off not Emulated System Off. Hence the device must not be in Debug Interface mode .
I want to retain the...
We're developing a low power communication stack, where every uA counts.
Currently, I have the system running at a few uA higher than expected, which I'm trying to track...
Hi,
We are developping an app using nrf52840. We started with the SDK14.2 and needed to migrate to SDK15.0 in order to use the long range. We are also using a Bootloader...
hi,
i am trying to on/off led on board(light_bulb code) which is controlled by the other board(light_switch code) with a gpio. when gpio is high led should be on and when...
I am using a NRF52832 and i want to burn a HEX bootloader that only jumps to my APP (i have already burned the Softdevice) when i reset it...
Can you help me ?
Hi,
I am trying to get the GPS from my thingy91, but it is not working. I can see that the board has CAT-M1 connection when I press the top button to get the GPS signal...
Hello!
I am trying to upload my compiled code via nRF Connect v2.6.2 to my nRF52832. But in nRF and also in J-Link RTT Viewer v6.46d it doesn't seem to connect properly...
Hello, I'm developing a BLE peripheral + Zigbee Coordinator, starting from ble_zigbee_dynamic_template of nRF5 SDK for Thread and Zigbee v3.1.0. Both applications (BLE and...
