Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi all,
I have been using nRF devices since a long time but recently I stumbled upon a problem statement where I need to create a mesh network. Here I have to have a master...
Hello, thank you for taking time to review this. I am trying to setup a serial DFU setup for the nRF52 on the nRF91 DK board. I am running into problems getting it to work...
In the nRF Toolbox I found this Beacons option where i can update the UUID , Major and Minor of the beacon. How do I use this functionality of nRF Toolbox app?
Hello, I'm not very famililar with Airfuel, but I want to add in my device wireless charging function. I start searching solutions for this challange and I found Airfuel and...
Hi
I am facing problem with segger. Project get compiled and able to program hardware but hardware is not working until debug process is start. After put hardware in debug...
Hi,
I am trying to establish UART communication between two nRF52 Dev boards. I flashed both of them with UART peripheral example from 15.2.0 SDK and connected TX,RX and...
Hello,
Recently I'm working on the project that utilizes the nRF chip and the external memory MX25R3235F. The SDK is 14.2.
I'm trying to configure the peripheral and the...
Hi I am using nrf52832dk as master and slave for spi communication. I want to send below data over spi. 0x8000000008 0xEC000100C5 I am get confused in transfer function of...
Hey,
referring to my previous thread in https://devzone.nordicsemi.com/f/nordic-q-a/44298/running-usbd_hid_generic-in-nrf52832-using-a-custom-usb-module-mcp2200 . so am...
We are using the Development boards nRF52-DK from Nordic and trying to utilize the mergehex.exe downloaded from Nordic website.
using Segger Embedded Studio (non commercial...
Sir,
I have one nRF52840 DK and ADXL335 accelerometer. I need to get the 3-axis values, Xout, Yout & Zout, from the accelerometer and send through BLE to my nRF mobile app...
Hi,
I was going through generic_level_messages.h and generic_level_common.h files looking for the parameters for generic level status message.
I noticed that generic_level_messages...
I am using nRF51822 with SDK 10.0. I want to configure a GPIO pin which can wake up the MCU from SYSTEM OFF Mode and call its IRQ handler. Please find below configurations...
