hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Please consider the images bellow, which can also be found here and here . The images represent the structure of a BLE packet, and the units used are bytes. The question...
Hi there,
I have tested out the BLE-NUS SDK firmware on the NRF51422 SDK Board, and it responded well. When I ported the exact same code over to my custom board, I received...
Hi,
I noticed that I can't bond successfully with my device using iOs 9.1 with Nrf Master control panel iOs app. When I insert the PINCODE, the device immediatly disconnects...
So I just received my nRF51 dk. When I plug it into the USB port, the device starts to blink but is not showing up as standard USB drive? Any suggestions?
Gabriel
Hello,
what general setup can you recommend to realize a Final Product Test only with BLE for mass production! (Without any additional copper contacts or NFC)
Some facts...
Hi I was reading up on all your chips.. NRF24, BLE and also on IPV6 capable..
Below are my requirements. Can you make a recommendation on what setup to use?
I have 4...
Hi
Im developing a filter - repeater signal on S130, and I want to advertise with a peridod of 20 ms for 10 seconds timeout.
I'm confused with FAST ADVERTISING AND SLOW...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
