Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello,
why did you chose to remove the S130 1.0.0.3-alpha from the relasenotes and merge it with the latest version? I don't think that's the way it works. Now we have...
Hi All !
I was read many posts about this function and do not understand how to check if all data is deleted.
In my situation I do:
Start advertising for bonded...
My devices in the field have firmware that saves an error code when it gets thrown and then sends it to a central so that I can see if there are errors with devices in the...
Hello,
I am using the sd_flash_write function. If I use this function without the nrf_delay_ms() function (see code below) the data is not being written.
sd_flash_write...
I would like to know if it is possible to log realtime sensor data to flash while advertising. I would like to have a device which transmits real time ECG data over ble UART...
Hi
I am struggling to change the device type on examples setup for nrf51422 to nrf51822.
If I change the setting in "options for target"/device I get the failure message...
I changed the multilink central example to some custom code. However, it seems like I've run out of space. But I don't under stand how this is possible because I selected...
Using gcc-arm-none-eabi-4_8-2014q1-20140314
Using nRF51_SDK_8 Using nRF51 dongle
Build in nRF51_SDK_8/examples/peripheral/blinky/pca10031/s110/armgcc succeeds...
Hi there,
When i disconnect the keyboard, the nrf51822 will restart advertising in directed mode.
And then on_adv_evt() will receive BLE_ADV_EVT_PEER_ADDR_REQUEST event...
Hi,
I want to use BLE for following situation and I wonder if it is achievable.
I have a 3 boards with nrf51822. Two of these boards have mpu6050 sensors connected to nrf51822...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
So, we have been developing our firmware (for a while now) against a SoftDevice version called 6.0.0-1 alpha. We are getting close to production time, so we wanted to switch...
I had a product working with S110(BLE peripheral).
I am trying to get same BLE feature working on an product working with S210(ANT)
So I chose S310 to have both ANT and...
Hi devzone...
My setup is nrf51422 dk with soft-device S110 on the server side and on the client side i am running MCP 3.8.0 on a PC using usb dongle.
I am using Queued...
