Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
I'm currently troubleshooting potential timing-related collisions associated with the NRF radio. I use a custom protocol on a single specified channel (no frequency hopping...
Hi, I have a custom board built around a nRF9161. When I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the expected string. All other commands...
Hi all
I'm working on custom board build with an nrf9161. Right now I'd like to use a gpio as input with interrupt for i2c captor icm20948. So for I've searched and I think...
Hello.
I have 2 designs of PCB to make, I have their schematics almost complete. Both use the nRF52840.
My doubt is if for each PCB, if I will be able to use at the same...
Hi
Can you please supply me with the mechanical dimensions for the nrf52840 dk? I can not find anything. I would like to have the dimensions of the mounting holes in relation...
Hi,
Previously, I used the nRF52840 to work as a host. Similarly now, I hope to use the nRF52832 to work as a host, but it seems that this cannot be achieved simply by changing...
I have a custom board with a nrf52832 chip on it and I am currently trying to build my own application for it.
I have successfully managed to compile and flash it using...
Hi,
We want to implement capacitive sensing of nrf53.
Can you help how I can use the nrf53 for capacitive sensing feature, as there is not much information given in datasheet...
"I'm trying to set up two nRF5340 Audio boards - one as a unicast client (gateway) and the other as a unicast server (headset). However, I'm encountering errors with my prj...
Hi
I'm looking into using the nrf52833 and/or nrf52843 for a long range mesh network. Since I require long range, but not high bandwidths, using a coded PHY seems appropriate...
Hello all,
I'm new in to development with nRF Connect and Zephyr RTOS, I have been reading the documentation and looking at the QA but I'm still unable to achieve a "low...
