Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi, all
I have some issues about developing on nRF connect SDK with VSCode:
Go to definition for macro always jumps to the wrong place. For example, BT_DATA_BYTES...
Hi all, I am using nrf52 with Softdevice 113 v7.0.1 and SDKv16 and FreeRTOS v10.0.1 and I am experiencing some issues with FreeRTOS timers expiring earlier than expected when...
Hi again,
A small edit to make this clear: Is it possible to update netcore using a single slot setup
After asking on another thread regarding something similar Simon...
I want to develop a low power device which enables connectivity for reading and writing data to its internal flash. The access should be with NRF_UART application
The access...
I was at 1st trying to use libuarte and it worked. However, talking to Edvin has convinced me to use something else as it is very resource heavy and I do not particularly...
Hi, I'm trying to connect an external I2C device to the nrf9160DK and read some registers. I'm using NCS v1.9.1.
I have my file nrf9160dk_nrf9160_ns.overlay defined like...
Hi!
I have been struggling with this for some time now.
I have a custom board with a nRF52810 that I want to run the ble_app_uart example as I wrote above.
I have made...
Peer Manager:
1. I am not sure whether my Nordic board and mobile app is just connected or paired, I am able to transfer data between the board and the mobile. How to...
Hi,
I want to make an emitter and a receiver for AOA. I have seen that the example i have to use is " Direction_finding_connectionless_tx (and rx)" but when i open it on...
Hi,
I'm using two UARTs on nRF52840 with SDK17.1.
My issue is both UART works individually until they receive messages at the same time. Both of them receive an RX overrun...
Hello,
NCS1.9.1, VSCode, peripheral_lbs
nRF5340-DK got error:
undefined reference to `z_impl_k_busy_wait'
nRF21540-DK and nRF51840-DK work well.
Best re...
Hi,
I was measuring the time it takes to boot to my application based on the nRF52832 and the time I measured was excessively long.
I'm using a PicoScope DSO for observing...
Hi,
I've been requested a feature regarding buttonless OTA DFU that I'm not sure if it's feasible or advisable to implement.
The feature is that once the OTA is successful...
