Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi everybody,
I have problem with my nrf9151-DK. If I switch my kit do AT-Command mode (I use Serial Terminal of Nordic, v 1.4.3), I am not able to switch my kit to PPP...
I'm porting some code from nRF52832/nRF52840 to nRF54L15 using the MPSL timeslot API. The old code uses MPSL version v2.5.1, the new v2.9.0.
The firmware opens a session...
I am evaluating Bluetooth Periodic Advertising with Responses (PAwR) using a NRF52840 Development Board. I am very satisfied with the development environment and the nRF Connect...
Hi,
normally, I would set the CMAKE_BUILD_TYPE to `Debug` to enable Cs "assert" function (not define NDEBUG). Zephyr (and Nordic-Zephyr as well) has the `CONFIG_ASSERT`...
Hi
I want to check the nRF54L15 ADC Rsource value
As below pic., P1.07/AIN3 input voltage will be 0.6V (1.8V divider by R429 & R428)
So the Rsource value will be R429...
Hi,
I am trying to build an app for nRF5340 and I am getting the above error. When I look into my 'C:\Projects\nrf\nrf5340_coap\build\zephyr\include\generated\devicetree_generated...
For firmware development purposes, my code makes heavy use of asserts, primarily the standard library assert() macro because that is available on all platforms that my code...
I’m currently working on a project where I need to protect specific registers in the UICR (User Information Configuration Registers) from being overwritten or erased during...
Hi,
I am using the nRF5340 Audio application under NCS v2.8.0 as a Unicast Client (Central).
The nRF5340 is connected to hearing aids.
When moving out of range, audio...
Hello everyone,
Our team is developing an indoor positioning solution and is exploring Bluetooth channel sounding as a core technology. We are currently using the nRF54L15...
We want to understand any surprises with using nPM1100 on existing or future products.
I just bought two nPM1100-EK units and finished the first round of my evaluation....
We could have found "transmission delay" in 2ch Audio recording sequence.
Here are the detail about the environment of DUT, and phenomenon.
Please find the attached file...
Hello!
When turning on the board, USB connected to the Mac, a software drive named JLINK keeps mounting and being dismounted, as on the video of this link: JLINK video Only...
Hi there,
How can I copy and customize an existing Zephyr driver?
I'm looking to extend the implementation of the LIS2DH driver in Zephyr.
The driver does not support...
