Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The registered schedule was changed to inactive, but...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
Hello,
we are using a Flutter App on iOS and Android.
With iOS the data transfer is as fast as expected, but Android seems to have delay of 2 seconds between the data...
I am adding a bootloader to my project for OTA DFU.
App core and net core update was successful in the 1st stage bootloader configuration, I'm configuring a second stage...
Does the NCS stack + nRF7002 support scanning while connected? I would expect it could, to support handoff, but getting errors.
Using nRF7002-DK and NCS 2.8.0.
Compile...
Hi, I have an issue when I try to install the nRF connect SDK. I am using Linux Fedora 39, trying to isntall SDK v2.5.0. Steps taken so far:
Download and install nRF command...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
Hi,
I am having problems getting PSM mode, or at least getting a decent power consumption in PSM mode, because I think the PSM in working properly.
I am using the EVB...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
Hi,
I am currently working with the nRF5340 Audio DKs and have successfully implemented the gateway and handset functionalities.
Now, I want to extend the system by enabling...
With the mcuboot enabled, I'm not being able to disable the boot banners even by doing the below settings in prj.conf file.
CONFIG_NCS_BOOT_BANNER = n
CONFIG_BOOT_BANNER...
Hi!
In our project, we need to send cloud-to-device commands. By "command" I mean a request to do some short action, not a request to change device's configuration/state...
