Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Hello,
I have been trying to get my brand new nRF52840 Dongle working as an 802.15.4/Zigbee sniffer, but I am not able to capture any packets, even though the interface...
I compared the S132 and S140 protocol stack files. The S132 file does not occupy the 0x26000 address, while the S140 does occupy the 0x27000 address. However, the application...
Hi, I've spent a few hours trying to figure out a way to use the onboard PDM microphone on Thingy52 with the nRF Connect SDK.
I saw a pull request for one from a member...
Hi nordic:
I am using NCS 3.0.0 and VSCode. I was able to compile the sample code in the SDK some time ago, but now I am getting the following error when compiling the sample...
None of the buttons work, most errors are similar to as follows but specific to each button:
Error running command nrf-connect.app.createBuild: Could not find SOC. This...
Dear nrf team,
We are facing an issue with the eSIM on our nRF9151 board. The SIM 1.8V pin on the nRF9151 is not supplying 1.8V. We have checked this using a multimeter...
When trying to flash the NRF Bootloader via OpenOCD, i got this error from command line:
nRF52 device has a CTRL-AP dedicated to recover the device from AP lock. A high...
Hi team,
We are evaluating Amazon Sidewalk from Sidewalk SDK v1.0.1 , the hello-sidewalk sample is ported onto our in-house prototype board (nRF54L15). We’ve:
Provisioned...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
I'm attempting to use the Settings API save and retrieve data from nRF52832 FLASH memory. I can build and run the example application provided in the Settings documentation...
I want to use the UART to receive data, but that doesn't look possible if I use the Logging Module. I don't see where the logger module will interrupt my code to tell me I...
The NORDIC tutorials are great for demonstrating how to use GPIOs to drive LEDs and read buttons.
However, I need an 8-bit bus to exchange bytes with an external display...
We are using the nrf mesh sniffer android app to record logs of our mesh network to try and track down some weird behaviors possibly related to the messages being sent. The...
