Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello.
I know that I can change the interval of the advertize event by changing the advertize interval, but I don't know how to set the interval to be sent to each channel...
Hi, We did design our own board/pcb using the nrf9160, but we have a problem to connect to network/lte. I did some debugging and I found out that when the method lte_lc_init_and_connect...
Can you please tell us what is the power consumption in Idle State with DRX = 1.28s and Sleep State with DRX = 1.28s? And an estimate with eDRX at 5.12 s? We are asking because...
Hello, I am using nRF52832 dev kit. I am trying to get lower current consumption. I used ble_app_blinky example and disabled the NRF_LOG. My settings are below:
Role: Advertising...
Hi, I used my NRF52840-DK for few times but suddenly the jlink connection was not detectable. Before the Jlink failed, the main controller on board did not bring up the board...
Hello,
I Cant upload BLE Code on nRF52832 breakout board from nrf52 Dk using Segger studio. Other codes such as blink are uploaded successfully. But there is problem for...
Hi,
I am trying to use radio notifications (mpsl_radio_notification.h) to call notify with data just before central connects. I do this with no problem with NRF52840.
...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
Hi. I am working on firmware for nRF9160 based IoT device Already found a way how I can switch between two different images in flash from the current firmware and it's super...
Hi,
I'm trying to achieve a higher transmission speed between nRF9160 and PC on Thingy91 using connectivity_bridge from NCS 1.7.0. On the 115200 everything is working fine...
Hi,
I am trying to flash one nrf52-DK using the other nrf52-DK.I am using nrfconnect App to flash on Linux.
I am getting an error as:
ERROR Could not fetch memory...
