Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi I have a nrf5340 pdk version 0.8.0 (PCA10095) When I plug it into my Win 10 (latest version 2004) device manager tells me it sees 3 comports
When loading the 'Peripheral...
I want to change between LTE-M and NB-IOT, however lte_lc_system_mode_set(); is not actually changing the mode.
I am doing something like this
I can't rely on PSM/eDRX...
Hi Nordic:
Because my device(peripheral) sometimes is connected by a unknown center device, I want to get some information from this center device,
and try to find it...
Hi,
I have just added a VS service (PCA10040, s132 7.0.1, embedded studio v5.10a x64)and I understand I need to increase the ram given to the softdevice. However, I have...
Hello,
We are developing a product using a nrf52832 and an APDS-9306 ambient light sensor. This sensor interface using the TWI peripheral. We are using the 14.2.0 SDK and...
Hello,
I have a problem building Asset tracker from SDK application example with simulated GPS data. After building an error message shows.
B 48 KB 132.29% B 64 KB 13...
Hi, I have started development on nRF52840 DK. I have 2 boards one is working fine but the other one making an issue. When I tried to connect it shows the following error...
When using the sd_ble_gap_sec_params_reply function to reply to a pairing request and declining it with the BLE_GAP_SEC_STATUS_TIMEOUT reason, nothing seems to happen, the...
Hi,
I work on the nRF52840-Preview-DK board. I try to make a ble to uart bridge and I start with the nRF5 SDK 14.0.0 ble_app_uart example.
I compare the current supply...
Hello,
I just solved the previous problem thanks to the reply. Thank you a lot.
But, I have one more question..
I was tested UART central example( ble_app_uart_c)...
Hello, I am working on a firmware for nrf52832 custom board, whose purpose is to light an onboard LED if another nrf52832 custom board (same design) is near to it. The other...
Hello,
I am developing a zigbee coordinator with a BMD340 module (using the nRF52840). I want to support several third party device with the coordinator. I am able to connect...
Hi, We have a smart product, which has two application scenarios. One is the use of BLE peripherals, similar to sports bracelets; The other is the 2.4g private protocol mode...
