Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
We plan to use 2x nRF52840 in our new product design, and want to know if they can share a common 32kHz crystal. From the following discussion it appears to be possible, but...
Which is the preferred way, accessing sensor via the TWI
1) NRFX_Driver
2) TWI HAL
what options do I need to select in the SDK_CONFIG.h to use the twi_driver api.
Hi all,
I know this question has been asked before, but a long time ago.
Is there any emulator for the nrf51 that I could make use of? I've tried using QEMU , but...
I have a peripheral and central units, both based on nRF52832.
Both of them have to be able to initiate a messege to the other at any time.
Both of them have be able to...
Hi,
I am a newbie to BLE 5 and I need some consulting regarding a system configuration.
The system is as such:
first unit (board #1) is an electronic lock that is installed...
Hi,
We are soon will be evaluation the nRF52 chip for BLE5 application. My question is whether the chip has a protection against Blueborne hack?
Regards,
Gil Fonea ...
Hi All
I am right now working with nRf52840DK on Segger Embedded Studio (S140 SoftDevice), and I am trying to read my BLE channel map by function , but I did not get the...
I'm wondering if anyone uses unity.c for unit testing and managed to change the print function to segger rtt in order to read the output.
According to unity
By default...
Hi All
I am now working on Channel Selection Algorithms in nRF52840DK by Zephyr. For right now, the choice between Channel Selection Algorithm 1 and 2 could be made by me...
We have been using the same inductor that Nordic uses on the dev kit board, the Taiyo Yuden LBMF1608T100K. We are trying to make some new boards quickly and these are not...
Dear Nordic,
I met a problem while using nRF24L01+ about MAX_RT interrupt.
In my codes, I disabled RF HW retransmit (hal_nrf_set_auto_retr(0, RF_RETRANS_DELAY);) because...
Hello,
From the datasheet of nRF52840, I found the 32MHz crystal's package is 2016 (reference circuit).
Is it necessary? Can I use bigger package?
Thank you.
Hello, I am trying to create a clone of a temperature sensor with the nRF52840 DK. I catched all important data from the sensor to configure the nRF52840 DK. But I cant find...
Hello.
I am trying to implement a Zigbee Network were sensors will be posting data periodically to a Coordinator.
I was looking into the examples provided with the SDK...
Hi team,
Our customer use nRF52810 to be an RF dongle.
They meet an question was about the high PER when there was an headset dongle was near nRF52810 as bellowing....
