Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
NCS v2.8.0
nRF52832 DK & nRF52840 DK
peripheral_uart unmodified example
nRF52832 DK with peripheral_uart example has about 1.3 mA current when LED off and sleep mode...
We want to use a BL6554PA (based on the nRF52840) as a thread node and enable the integrated Skyworks SKY66112-11 front-end module with PA and LNA to increase our range. I...
Hi All.
Trying to complete Lesson 6 Exercise 2 from the course nRF Connect SDK Fundamentals made by the DevAcadeny, I connected the Thingy53 to my computer through USB-C...
Hi,
As part of some verification purposes, we need to test out peripheral with the nRF connect Bluetooth low energy app. We have the peripheral set to 2M, DLE enabled and...
Dear Nordic-Support and community,
I am developing a system where a Thingy91 device needs to:
Dynamically connect to a specific BLE device that sends data like Heart...
In version 2.9.0, I modified the JEDEC ID.
The system is supposed to send a "Deep power- down enter(0xB9)" command after reading the JEDEC ID.
However, after the system...
Hi,
I am trying to evaluate the provided smp_svr sample with the BLE DFU on the NRF52840 dongle after I have already tested it on the DK.
I get the following error message...
If we subscribe all attributes of cluster of device connects to coordinator will it make issue? we have noticed its dropping many values if subscribed at same time. if values...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello all,
I'm working on nRF-9160 and nRF-9151.
What I want to add into SLM application were:
Configure to communicate through UART2 since it will be working with...
Hi,
I'm currently developing a headset application using the nRF5340 AUDIO DK. The thing is, I would require 2 AUDIO DKs (one for headset and one for gateway) to implement...
Hello,
I am wondering if what I am seeing is expected. I tried flashing the modem fw on the nrf9151 using nrfjprog.exe (v10.24.2); which I am able to do successfully, but...
Hello,
I have a Friend SoC with nRF52833 via SPI HCI communicating with my nodes that are nRF52833 MCUs. The nodes are LPN nodes sends data to the friend and awaits a reply...
When using the Serial Monitor, sending AT commands does not show any response from the Actinius Icarus board (nRF9160) Is there any way to resolve or debug this issue further...
Issue Description
The application starts successfully, initializes the modem library, connects to the LTE network, resolves the MQTT broker's address, and establishes an...
