I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
We have an nrf5340 custom board and during frequent BLE connections/disconnections sometimes it seems the netcore gets stuck. We are connecting to an iOS app and...
Hi:
Pls help me!
I use ncs v2.6.1.
C:\ncs\v2.6.1\zephyr\include\zephyr\sys\util_internal.h
When I check #define Z_IS_EMPTY_ (...) No matter what I input, I can't get...
Hello Nordic team and community,
I’m exploring the possibility of creating a mobile application (potentially using Flutter or native frameworks) that would act as a Distributor...
Hi,
I'm facing a critical issue with our sensor's power setup and would really appreciate any insights or suggestions.
Our sensor is currently using a CR2477 battery,...
Hi guys,
simple question based on your experience: what is a realistic data rate between an Android device and an nrf52805 with S112 on board?
I tried a lot of tweaks...
Hi, in our project we use the nRF52832 and a external flash memory MX25L3206E connected on this pins:
Take note in this project we also use SPIM0 to manage an IMU and...
Hi, I just purchased new PPK2 kit from mouser.
But after trying to open it via nrf Dekstop app it gives and error
2024-11-19T11:57:53.845Z INFO Selecting device with the...
Hello, I am trying to achieve a few uA current in nrf9160 but with even all conf off and empty while loop or even without the while loop the controller is consuming 5mA which...
We are currently working on a project based on nrf52840 and using connect sdk v17.0.0.
It is currently in development phase but eventually we are planning to use nrf5340...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
