Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
I have been looking at BLE with the Nordic products from the perspective of someone who gets a hand wave of an idea and moves forward. I have developed Nordic firmware but...
We have been able to enable coded phy with PAWR using
```
struct bt_le_adv_param *params = BT_LE_EXT_ADV_NCONN; params->options |= BT_LE_ADV_OPT_USE_IDENTITY | BT_LE_ADV_OPT_USE_NAME...
Hello,
I'm using nrf52840 DK to test 1khz tone. The nRF Connect SDK version is v2.6.0.
I put a pcm raw data array of 1khz tone in the code and used i2s write to send the...
Hi everybody. Recently, I've spent nRF Connect SDK Intermediate online course. I could add firmware upgrade ability using FOTA and now, I can update the firmware using nRF...
Hi Nordic Semiconductor Expert,
I would like to measure the BLE throughput over nRF52805.
Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
Hey, I am trying to run F8100 development board with nrf52840 development board, while I make the connection simply like CS-D10(Arduino pin layout presenting), MISO- D11,...
Hello. I would like to receive the passkey value that the user entered when pairing Bluetooth and modify it. Originally, it was said that if you enter "0000", you have to...
Dear support team,
I'm using nrf9160 and SLM to create a UDP server and client, and communicating between them. When communicating every 300 ms, there are times when there...
Hi, I got a problem with the NRF Connect plugin for VSC.
I have a project which has that structure:
workspace ├── app │ ├── src │ │ └── main.c │ ├── CMakeList.txt │ └...
Hello everyone,
I am working with nrf connect sdk toolchain v2.6.1.
My project requirements are as follows:
1 MBaud UART Async API
Two Modes for UART RX
fill...
Hello, I installed the the toolchains 1.9.0(working on existing project) successfully. However, i am not able to install manage SDKs.
This is my output:
