I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
I am attempting to write a routine that monitors the heap in order to track down a memory leak. I've seen similar tools on other platforms and found them quite helpful. To...
Hi,
Previously I have merged spi with ble_app_uart on NRF52832 based ISP1507 test board . It has performed successfully which was enough to carryout the evaluation phase...
Hi. experts, I tested [TC-ACE-1.2] Subscriptions with Test harness, which is UI-Python. I execute it on Docker,./certification-tool/scripts/otbr/otbr _ start.sh; And write...
Hello.
I'm trying to figure out which microcontroller is best for my use case. I need to have as many bluetooth low energy concurrent connections as possible and the device...
After rummaging through the awful and extremely limited documentation relating to external programming using the NRF52840 DK (so I don't have to pay for the $700 scam device...
Greetings
I am trying to use the BLE fundamentals exercise (Lesson 4 exercise 2 solution) to send actual sensor data, that I receive via I2C, to my nrfConnect app.
When...
I have a question about for LE. In my understanding, BT connection must confirm each profile, and it is able to connect same profile that each products have. For example,...
Hi,
I just wander why in the peripheral UART sample for the nRF5340-DK (ncs, SDK 2.7.0), the prj.conf doesn't include the internal capacitor configuration:
prj.conf file...
I realize that Bluetooth is the primary target of these devices these days, but I wanted to try an old tried and true example on the nrf5340. I am rather familiar with esb...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_rsp, after changing subevent_interval to 8, I meet following error:
*** Booting nRF Connect SDK v2.7.0-5cb85570ca43...
