Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Good day
I have a custom board using an nrf9160 device. On the board I am running a variation of a lwm2m client. I have a question regarding a network connection. Why is...
Hello,
could someone point me where I can find the most current / state of the art example for the BLE UART app for the nRF25840 Dongle?
The version in the nRF5_SDK...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
Hello,
we run an application on a custom board with nRF52840 powered by an external power supply and buffered by a supercap. The supercap then provides the energy for the...
Hi,
I have 2 nrf52840-preview dk board. All of a sudden both the devices are not working any more.
I have referred to some suggestions and tried all the below cases and...
Hi!
Absolute beginner here. I'm trying to use npm1300 (using the evaluation kit for now) with an RP2040 microcontroller (also using RPi Pico dev board). I am powering RP2040...
Currently, I'm using nRF5340 Audio on a homemade board, and I've managed to get the sound input from the gateway as a LINE input and the sound coming out of the headset, but...
Hello ,
I am trying to program external custom board through another nrf52dk via SWD interface to check if external programming method works. The connections between two...
We are using BLE and QSPI at the same time and want to have maximum RF range. Sensor data is collected, encoded, and written into flash via QSPI. This goes on for a few minutes...
I have a question: Is it possible to use BLE Long Range mode (Coded PHY) in the NRF52840 with mobile phones? If not, is there a solution to use it in parallel with normal...
I am using NRF52840's NFC with apple wallet but it requires certification from Apple to be used as tag reader. How can I get it certified so that I can read data from apple...
Hello,
I need to be able to send/receive binary data over this BLE UART Service (bt_nus) on macOS. I'm using the peripheral_uart sample project with no success. It seems...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
