At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
We are working with adafruit Nrf52832 and have a weird problem, the Ground pin and 3.3v pin is shorted and it also shows a 3.3v between them. Can you please help regarding...
Hi there,
I wanted to bring up the Bluetooth samples on NRF5340 development kit on NRF CONNECT SDK v2.2.0.
After building and flashing it, I can see the UART log on my...
Under:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_thread_tools.html#configuring-a-radio-co-processor
steps listed for 1 and "nRF52840 Dongle (USB...
Hello,
I am starting working on a nRF9160DK board, but I am new to this and I am a bit lost.
Using the Dev Academy course and example, I was able to make a small project...
Looking at the docs: nrf/ug_thread_architectures.html
I see the note "This platform design is currently discontinued by nRF Connect SDK." for "Network co-processor (NCP...
Hi All,
We have 2nos. of NRF5340 DK board, in which we are trying to run the "broadcast_audio_source" from nrfConnect SDK 2.2.0 sample installed from nrf Connect desktop...
hi team,
i have trying to wrote a code for saadc module in segger 5.40 using nrf52840 controller. whenever i am trying to increase the Acquisition time the sampling value...
Hi, I want DFU the NRF52840 using the UART. Please let me know the following quires .
Process-
I want to create two partition of memory one will store the my main application...
While running the mentioned code I am getting stack overflow error continuously. Can someone help me understand the reason behind that and what can be done to resolve such...
Hi, I am trying to do the SPI communication between a SPI master and two SPI slaves. I am using NRF52840 Dev Kit as SPI master and 2 ESP32-S3 as SPI slaves. I am using SDK...
I have added WDT to the blinky_freertos sample.
And I am debugging with SEGGER ozone.
building with SDK17:
If you reset the software in the debugger and start it,...
I have this 2,4" TFT Display with a IL9325 driver! I need to implement a 8bit 8080 Parallel interface.
image description
This is my 8 bit write function:
// Write...
I have this as nrf52840dk_nrf52840.overlay in my application directory:
/ {
lightStrings {
compatible = "gpio" ;
lightString0: lightString_0 {
gpios = <& gpio0...
Dear Sirs!
I am going to use nrf_drv_spi_xfer to read 15 bytes periodically (Approximately each 4 ms) according to GPIO (GPIOTE Event via PPI). To do it I am going to call...
