Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
my project is based on the example 'ble_app_proximity' from SDK ver 17.0.2. When I set a longer DEVICE_NAME, for example
the string is cut up after the first 12...
Hello everyone,
I am developing a wearable device using the nrf52832 chip, sdk11.0.0 and s132_nrf52_2.0.0_softdevice.
Because of battery capacity limitation, I have to...
In UART async mode ( CONFIG_UART_ASYNC_API =y) the UART transmit data and receive callback works fine. I've been able to set up the callback and enable the rx.
After switching...
I'm currently setting up an environment in Visual Studio Code because the roadmap suggests going there.
I have experience with Segger and Nordic Segger and with Zephyr....
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi, I am coding an application on nrf connect sdk 1.9.1. which requires to send some data at 25packets per second. and each packet will be ~37 bytes. On the receiver side...
Summary: My custom board with an external crystal is consuming 208 µA when powered down under Zephyr, and I need to reduce it to less than 20 or so.
My board is based on...
Hi,
I'm working on a project trying to build a simple application on my own customize board with nrf52833 SoC.
After the configuration to my own board(Leds, button GPIO...
I'm attempting to store log data on my nRF52832 using the little file storage, and then allow a client to access this over BLE. From what I can tell, the data transfer can...
Hi,
I am using device nRF51822-CFAC, the SoftDevice is S130_nRF51_2.0.1(Id: 0x0087). In my project's General Options->Target->Device, I selected "NordicSemi nRF51822-CFAC...
Hi,
Could help me please?
What I need?
1) set GPIO pin as input with internal pulldown and set IRQ for Rising Edge.
In .overlay I add my pin like that:
Then in...
Happy Friday! So, I've fully funded on Indiegogo and now I'm in the application development stage. I'm new to development but I'm trying to build this app myself.
So far...
Hello, I have a need to include a header file that I have defined in one of the Connect SDK .c files. For the purposes of this question, let's say I want to #include "myfunctionsandvariables...
I recently bought a pca10059 and inadvertently erased the bootloader while using a script from another project.. (it did --recover unfortunately).
I'm using the debug out...
