Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello everyone,
I am writing an application with three sensors on the same SPI1 interface on my nRF52840. See the following devicetree section:
For all sensors, I use...
I’m following the nRF54L Series Express Course – Lesson 5: Power Consumption Demo Part 2 sample code, using nRF54L15DK to test the deepsleep → wakeup functionality. However...
I work nRF54L15 with NCS311.
I want to save application's parameters on UICR.OPT[].
But it looks like somewhere in OPT is used by the bootloader.
What parts of UICR...
Hi, i am working on the nrf5280, and I have set up BLE with NUS so I have a shell and logging over BLE, as well as logging over UART. I have a python script running that connects...
Hi,
I'm preparing to run some openthread code on an nRF5340DK using the latest SDK and toolchain v3.1.1. A simple program works fine until I set the CONFIG_OPENTHREAD...
Dear Sir,
I have purchased nRF5340 DK (Will call it device hereafter) and am trying to bring it up.
I have connected the device to Linux but the device was not detectable...
I’m testing the nRF9151 DK in India and trying to use the nRF Connect app (Quick Start guide) to connect the device to the network.
Board: nRF9151 DK
SIM: Onomondo...
I have a nRF52DK board that I loaded the peripheral_uart program in a while ago. I tried to get the board running again but when it calls err = settings_load() it just keeps...
I'm currently trying to integrate Memfault to my project that is using nRF9151 DK. Memfault was working fine until I turned on these configs:
# Collect LTE Metrics CONFIG_MEMFAULT_NCS_LTE_METRICS...
The application here is reading a Manchester stream on a GPIO. which comes from a MAX41473 radio IC.
Decoding is working fine using GPIOTE, timers & PPI to time & decode...
Hi,
I have two nrf9161 dev kits. I have flashed the firmware 2.0.1. Then I flashed the hello_dect example.
Now I always get an error and the program does not start. *...
Hi,
I am able to do some stuff partially using the command
$ west build -b nrf52840dongle_nrf52840 -- -DDTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=prj_cdc.conf
With...
Hi guys, I am using the SDK v2.9.0 and the toolchains b620d30767. To add the build configuration for the sample peripheral_uart, the console print some error log.The log as...
Hi all,
Im' tryint to acheive a aws fota firmware update on my custom nRF9151 board but I'm stuck. Here is my setup and what working
- Custom board build with a nRF9151...
Hi,
I would like to perform channel sounding on nRF54L15 DK,
I tried to compile sample "channel_sounding_ras_initiator" in nRF Connect SDK v2.9.2, but error message says...
