Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
Code example: nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_ble_uart_freertos
Board: custom board with nRF52840
What are the fastest and easiest steps to make this...
Hello,
I am trying to code nRF52840- DK with MAX30003 ECG Board Using SPI. I have referred Arduino Uno Code for MAX30003 ECG.
I need some help for Driver Development if...
Hi,
Is there a way to dynamically disable only the fork of a PPI channel or should I go through disable-free-alloc-assign sequence?
Will nrfx_ppi_channel_fork_assign...
hi, nordicer:
two device, a peripheral and a apple phone as central. we want to support scan request and response with ADV_IND mode, I understand as following:
(1) peripheral...
Hello,
I use the LAIRD module BL652 with the nRF52832.
My project consist of do a synchronous between many board. Each second, I restart a timer of 1 second.
I include...
Hi guys!
I want to add SPI to my BLE project to read some data from my gyro.
Adding other headers was no problem, but when I want to add some code from the SPI-Example I...
Hello,
I am trying to run mesh DFU examples in following environment:
Distributor ID: Ubuntu Description: Ubuntu 18.04 LTS Release: 18.04 Codename: bionic
I have installed...
I am in the process of porting a current production application from SDK 13.0.0 to SDK 14.2.0 https://devzone.nordicsemi.com/f/nordic-q-a/39494/dfu-migration-sdk-13-0-0-s132...
Hi!
I used nRF Connect Programmer (desktop version) for writing firmware connectivity_1.2.3_115k2_with_s132_3.1.hex. And nRF52840 dongle doesn't display in the device list...
Hi everyone,
Yesterday I asked a question, but no one has answered yet.
Previous question:
https://devzone.nordicsemi.com/f/nordic-q-a/35067/nfc-tag-can-t-work-with...
Following file: nRF5_SDK_15.2.0_9412b96/modules/nrfx/drivers/src/nrfx_saadc.c
I've now just add gcc specific unused attributes.
This is just a work around. Best would...
Hi!
I am planning to move sample code of uart.because I port the function of uart to spi sample code.
now i take the SDK14.0.0 and uart sample(examples/peripheral/uart...
Hi, I can make a DFU over BLE with nRF connect 2.5.0 Bluetooth Low Energy, all is OK. I use my nRF52840-Dongle PCA10059 (Serial port: COM19 | USB: Nordic Semiconductor nRF52...
