How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
With a little research, I came to the probably erroneous conclusion that the "NRF_ERROR_INTERNAL" error I keep getting is likely caused by my not using a twi event handler...
hi
i did the setup according to border router setup guide on Nordic info center. all run fine but when i tried to run command ""panid 0xabcd" it saying not found
Good evening.
I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
Good day!
I'm working on NRF52 and its default timeout for advertising is 180s. But I am unable to stop the advertising event even after that. I tried to change the timeout...
Hello,
is there a certain amount of time the nRF52832 has to stay in RXIDLE between the reception of two packets when receiving several of them without disabling and re-enabling...
Hi, I'm a bit confused.... so far I was under the impression that SDK 12 was the last SDK that supported nRF51 development.
But now I found the section " Using the SDK...
I have a board with nrf51822 which is not equipped with HF crystal, but it has a LF one.
As pointed out in some other threads, calling HFCLKSTART on a board without functional...
Hello, I want to use the module app_mw_ble.c, but couldn't find its matching .h file, as a result, I got tons of "function declared implicitly" error.
For some reason,...
Good Day,
I am unable to connect my Rigado BMD-200 (NRF51822) to nRFgo studio using the J-Link EDU Mini. However, using the nRF connect application for Android I am able...
I need help configuring TIMER + DMA + PWM ( nrf52 ).
I would like to set the value of PWM with an interval of 100 ms and PWM configured to frequency of 20-40kHz.
Optinal...
I am using HRM demo application on nRF52840 DK with Samsung Tab-A. The nRF Connect App is running on the tablet. We are seeing that the dev kit gets disconnected soon after...
Hi,
The Bluetooth Developer Studio plugin fails to generate proper CP profile.
We use the last BDS version (1.1.3139) and the last version on the plugin (1.3)
Here...
Hi,
We are using nRF51822 Gazell protocol. We found that when host dbm is getting down to -61 or -62 dbm, the communication will lost. We had set it to +4db and use 250kb...
I have a question about how to build RSC (Running Speed & Cadence Service) ? especially using mbed compiler because I just found CSC (Cycling Speed & Cadence Service). like...
I am trying to add peer manager to multilink_central example on SDK14.1.0 based on the ble_app_hrs_c example. The code is running on nRF52832 and softdevice S132 5.0.
It...
