Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi,
The main problem is that I have a problem with NRF Connect desktop to erase/program nrf52840 dk. I get this error:
" Error: Failed with exit code 1. One or more...
Hi,
I'm using nRF52840 DK with ncs V 2.6.0. I plan to create an mp3 or WAV audio player. I tried using the MAX98357A with the i2s nRF52840 DK board, building a project i2s...
Dear Nordic Semiconductor Team,
We are currently working on a project that involves integrating the NRF5340 MCU. After reviewing the MCU datasheet and HW design guidelines...
Trying to use the QuickStart for the Laird Pinnacle DVK. The Quickstart only shows that JLink is detected, but not supported when connected. Even connecting directly to the...
Hi,
I want to get the tick count of the system with sys_clock_tick_get(). I am using a library for NFC reader chip ST25R3916B and provided library from STM requires a platform...
Hi,
I am using https://github.com/NordicDeveloperAcademy/nRF-Connect-SDK-Fundamentals lesson5/fund_less5_exer1 as base. I have set P0.26 as UART RX. Using the code below...
Hi,
We have 3 nrf5340 LE audio dks. Two of them are flashed as BIS gateways.
One as a BIS headset. Sample used: nrf5340_audio in ncs 2.6.0
I am able to stream audios...
Hi! I am taking reference to following issue :
I have implemented same method as discussed in above link. I am getting message on client side successfully only when code...
Hi, I am trying to set up unit tests for a new zephyr project on the nrf9160. I don't want to run them on the device and instead want to run them from the command line.
...
Hi, I'm currently using nrf5340 and central_multilink and central_uart example to build connection between one central devices to several peripheral devices. But right now...
Greetings
I am following along with the nrf SDK fundamentals, where I am doing lesson 3 exercise 1, which is related to printk. I have flashed my nrf5340 dev kit and it...
Yesterday I opened the nRF Connect for Windows utility and installed all of the pending updates. Now I am unable to flash or debug the project I'm working on using nRF Connect...
Hi All,
I was evaluating the throughput of NRF5340 using the DK. I would like to set the transmission power under 0 dBm of the peripheral device.
However, i was unable...
Hello,
I'm working on a project using the NRF52840-dk module and I'm having a problem with the Bluetooth functionality, during lesson 3 exercise 1. Despite correctly configuring...
Hi,
i just started working with nRF9160dk and i've been trying to implement the GNSS service (testing the Cellular IoT lesson 6 ex 1 exemple), although i've been testing...
