Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Dear Matter Support Team,
I have a setup where an On/Off Switch device is successfully bound to a Light device in our Matter network.
I would like to know which specific...
I am using the Ublox NORA-B206 module and facing issues with the debug option in the VS Code extension. The debugger fails to start, and I receive the following error message...
Hi Team,
We have a custom board with nRF9151 SoC that shows complete RF failure. The modem initializes correctly and detects the SIM card, but cannot detect any RF signal...
I'm adjusting my program with nrf52832 and nrf5SDK.
I attempted to use the parameter PM_PEER_ID_N_AVAILABLE_IDS to control the upper limit of the bound users.
However...
Hello, I am testing the power consumption of the npm1304 for the first time. To do this, I am using the PPK2 connected to the nPM1304-EK on VBAT and GND of the P1 connector...
Hello, According to the nRF7000 specification, the sleep current should be around 15 µA. Electrical specification .
We have a custom PCB with nRF9160 + nRF7000, and the...
Hello DevZone,
I'm testing the Matter OTA by using OTA provider. Referring to: Performing Device Firmware Upgrade in the nRF Connect examples
But it's too slow. Is that...
I want to update 52840DK FW using Matter OTA, but I have not found SOP, could you tell me how to operate?
BTW, I use Raspberry Pi4 connected with RCP as border router. ...
After flashing the official example hci_uar onto the nRF5415-DK, I proceeded to use "udo strace -o btattach.log btattach -B /dev/ttyACM1 -S 1000000 -R“ to bind it as an HCI...
Hello, I’m working with the nRF9151 and testing DECT NR+ functionality. I already have the binary image of the DECT NR+ PHY firmware and it works fine. I’m just curious—is...
Hi,
I've successfully incorporated MCUBOOT into software we developed for the nRF5340. I'm also able to start serial-recovery by activating a GPIO, reserved for this purpose...
Hi, I’m trying to build the github.com/.../neuton-nordic-thingy53-ble-remotecontrol project using nRF Connect SDK v2.6.2 . I added the BMI270 sensor on SPI3 in my DeviceTree...
Hello,
I am at the very, very early stages of my project, doesn't it even a name yet. Right now I am thinking of using nrf52840 for a Bluetooth operation while being supplied...
Hi,
I am working on a PCB with the nrf5340 and I have been following the reference schematics and the hardware files from the audio DK. I want to have the bare minimum...
Currently, I have configured cs-gpios in the device tree and loaded the SPI in the main function. Why is D0 (representing CS) kept high in my experimental waveform, and SCLK...
