We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
we have 10 nRF52840 DK's 8 are version 1.0.0 and 2 are version 3.0.0(purchased this week).
The older version 1.0.0(made in Norway) work perfect with our 3V boards...
Hi all, I got the nRF52833-DK 2 months ago. I've deployed the heart_rate_demo.hex example to it and it seemed to work. Now i'm trying to connect the DK to the PC again and...
Hi Everyone,
I am starting development of new project and we are using the module MBN52832.
Now I want to start my development for this board. I have a few questions...
Hello,
My questions is very simple but I found many trouble during the procedure.
I would like to export my project (created con VSCode) from my PC to antother one and...
Hello everyone!
While programming nRF52805 module, I am encountering an error in memory reading stage. Logs from the application (both Failure and success cases) are attached...
Hi, I am working on a Homekit project and the nRF Homekit SDK uses NVS settings to store data in the internal flash. Is it possible that I can add another partition in the...
Hardware:
nRF52840 DK
S140 Soft Device
SDK 15.2.0
Hello,
I want to confirm my understanding of the impact of flash operations on the nRF5240 when using the SoftDevice...
As far as I know, there is a limit on the number of packets that can be transmitted in each connection event of a Bluetooth transmission. Is there any configuration that can...
Hi,
I've been working on an implementation of BLE Mesh's Generic Sensor model using nRF5 SDK for Mesh v5.0.0. The sensor I'm working with is a temperature and humidity sensor...
In out project we have a nRF9160 connected through UART to a nRF52840 that's used for low power beaconing.
In order to configure the advertisement data on the nrf52840 we...
Hi,
I am trying to test the multicore example but when I try to build the application I have some errors related to python (maybe). The log is the following:
I don't...
What is the difference between nRF52840( QFAA ) and nRF52832( QFAA ) on hardware level? Do both of them have same footprint? Because I am facing difficulty finding the stock...
Hello,
I'm using the PPK2 to evaluate a DUT which is transmitting over BLE using NUS in SDK 17.0.2. I'm seeing very large variability over each transmission and was wondering...
Hi all, I am working on nRF52840 DK and wish to control the mesh light example using BLE central devices like Arduino nano ble 33, esp 32 and smart phones. I could not find...
