Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I noticed that if I set options = BT_LE_ADV_OPT_NONE in bt_le_adv_param I get a random address at each bootup and if I set it to BT_LE_ADV_OPT_USE_IDENTITY I get always the...
Hello,
I'm currently working with ISP2053 which is the nRF5340-based module.
The system, as the specific GPIO pin detects a low-to-high event, gets data from another...
Hello guys,
I'm trying to run uart example from https://github.com/andenore/NordicSnippets/blob/master/examples/uart/main.c extended by interrupts call after transmission...
Hi.
I cannot build a ble_app_uart Nordic example that I was able to build flawlessly three years ago and later. I wonder if anybody could give me a clue on what's going...
On Zephyr `2.7` I have following code to setup a SPIM on a custom board: Device tree:
main.c:
Now this no longer works on Zephyr `3.1`. I temporarily tried it with ...
Hello
I tried to install nRFConnect for Desktop, the latest version When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message....
Hello,
I works with Zephyr, VCS, SDK 2.0.0
I don't find how to get pin number from the DTS pinctrl .
In this folowing code, I want to replace magic number (uplighted...
Until toolchain update it was working well. But after toolchain update I cant even open toolchain manager . It just shows some exception like " Unexpected end of JSON input...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
Hi,
I saw here: nrf52840 802.15.4: mlme_start_req: nonbeacon-enabled mode doesn't work
that the SDK-Version 14.2.0 was not compiled to work with non beacon enabled mode...
Hello,
After upgrading to the new version with the help of the migration guide, there is an issue that I could not trace back to any changes.
If I am correct its about...
Im compiling an app in nrf sdk 2.0.0 which works well on the nrf52811
as soon as I add
CONFIG_NRF_802154_RADIO_DRIVER =y
into prj.conf
without even initializing...
Hi Everyone,
I am working on NRF52833. I have developed code for our project. Now in this project the phone app will connect with the device using BLE for which I have implemented...
