Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello, Dear Kenneth.
Thank you very much for your response and the answer.
I will change the hardware solution using a voltage detector, but I am not clear yet on the...
Hi, i have this message after installing nrfutil
I checked version of the python, checked requirements, tried to install from sources. I do not know what to do next
Hi, I am experiencing a strange case here where after an update from SDK15.2 to SDK 16, the noinit section of RAM is not working anymore.
When I encounter an error of some...
In v1.4.0 SDK, AES key can be written into kmu slot, but there is no related function for ECC key and RSA key in crypto/nrf_cc310_mbedcrypto/include/mbedtls/cc3xx_kmu.h file...
I am using an STM32L4 chip that sends an update to the nRF52832 on a ublox module over USART. I assume the nordic chip is in the bootloader during the update.
We get a UART...
Hi, I want to eventually be able to programme a custom built chip with an nRF52833 SoC on board, but first I thought I would try with a nordic Thingy:52. My setup is as follows...
Hi,
I have seen a few tickets with people not getting any CTE data received and program restarting after "Waiting for periodic sync lost..".
Did anyone get it to work...
Hi!
Continue the previous case
I try to run zephyr direction finding rx example direction_finding_connectionless_rx
It seems to me that the external antenna is working...
Hi
I am working as a member of a team owning nrf9160 dk. I want to work remotely with the same hardware they have. but right now I do not have physical access to the hardware...
Hi, I installed VS. The screen shot is shown below. How to open, Build, Compile, RUN and Debug sample applications and custom existing SES projects. May, some one explain...
I am trying to program my nRF51 QFAC, but it tells me to adjust my linker settings.
I am using the SDK 12.3 and the softdevice 130 2.0.1.
However, after I apply the...
MCU : nrf52833
SDK : Ver 17.1.0
SoftDevice : S140
I try to call RTC value to external RTC Module by TWIM in BLE authentication rw request event.
But MCU stop to...
Good afternoon,
I built and flashed the Bluetooth Multiple advertising sets sample in VS Code using the nRF Connect Extension Pack onto my nRF5340-DK and come across an...
I am trying to measure my battery level on my nRF51822 beacon board through the internal ADC.
The chip is just advertising itself every 5 seconds.
The measurement works...
