Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi,
I see in the nrf9160 1.2.0 AT document there is a command XFILEWRITE that suggests the GPS almanac can be written and persist in the modem.
Can you provide more documentation...
Hi, I have developed firmware on nRF52840 as a peripheral. Now I have to develop firmware on nRF52832(beacon) as central which scans the first device and connects and sends...
Hi,
I am using Zephyr configured to use the softdevice as the BLE controller.
I am looking to read and write a small amount of data to the flash for non-volatile storage...
I use nRFgo Studio 1.21.2.10 and J-Link V5.12f.
In nRFgo Studio I can erase my nrf52. However, programming with softdevice or application ends with error Unable to find...
Hi,
We are having custom HW and having NRF91DK and NRF52.
We have architecture as NRF91 and NRF52 (Central) is connected over UART and NRF52 (Central) and NRF52 (Peripheral...
Hi
I'm using direction finding connectionless_rx project from NRF Connect SDK 1.7.1 with NRF52833 and I want to sample the CTE with a 4MS/s sampling rate (sample spacing...
Hi, I have a project developed on Visual Studio Code and PlatformIO. Now I want to use the same classes with SEGGER Embedded Studio. How do i do? Thanks.
I am very new to this product and Bluetooth technology in general. I am trying to determine what I have done wrong. I have purchased the nRF52 dev kit and downloaded and installed...
Hi,
In our design we use Fanstel BM832 module, based on nRF52832 chip. We have failed spurious emission in ETSI RX mode. Rx LO at ~4958 MHz exceeds the limit by 0.3 dB....
Hi,
We are working on the iOS App development for our BLE device. Our query is that, “we have completed the connection with Ble device with our iOS application on first...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
