Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...
I am looking for to buy(I don´t have a 3D printer) a enclosure to protect my nRF52840-DK. It is not a good practice to handle because probably soon this practice will damage...
Hello, I just receive a nRF9161 Development kit and I'm completely new to both nRF9161 and Zephyr.
I want to start an evaluation project based on the nrf9161 lwm2m client...
Setup:
windows 11
VS studio code
Toolchain and SDK v2.6.1
hardware: nRF52840DK / PCA10056 (bought June 2024)
Using sdk/zigbee-Template as the base for the project...
Hi all,
I'm using an nRF5340 DK and I want to build a simple project that plays a sinewave to an i2s DAC (MAX 98357A, perfectly working on other development boards I have...
Hello,
I found that after bonding, I could still connect to another board that had burned the same code.
Here is all of my code related to pairing and bonding.
Central...
Hello,
I tried to find information about using the QSPI with external flash on nrf connect SDK.
My goal can be split into two parts:
1. Use QSPI with external flash...
Cant Flash Thingy52 on VS code after flashing once and also cant read sensor values of thingy on serial terminal. How can i flash on thingy52 smoothly like flashing other...
My programm uses both the non-secure world and the secure world, with the non-secure-world largely just calling functions inside a custom partition of TFM in the secure world...
Hi,
I'm working with a nRF54L15 within the nRF Connect SDK on Zephyr. I need an array which retains its content through soft resets, so in another RAM section than the...
Greetings,
One question on the nRF9161/51 capabilities: is the 3GPP Rel-14 LTE-M Cat-M1 larger UpLink transport block size (TBS) of 2984 bits supported (instead of 1000...
When debugging a connection using Wireshark and the BLE sniffer, one must select the device of interest from the device menu, or select "follow le address" in the key drop...
I'm checking the nrf_dm sample with NRF52840DK,nrf connect SDK.
Due to peer.c and dm.c create static thread,so I run debug and hope to get all thread and their priority...
Hi,
I am checking the i2c protocol with nRF Connect SDK and Zephyr through VSCode.
I created a very simple example where I push a button on the nRF52840 DK and I get the...
