At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello!
Our plan is to have the whole Bluetooth stack (softdevice controller, HCI, host) on the NET core and make APP core call the functions by RPC. The board is an nRF5340DK...
In my project, I need to set REGOUT0 to 4 , to achieve a VDD of 3 volts. In zephyr/boards/arm/nrf52840dongle_nrf52840/board.c there is an example showing how to do this in...
Hi,
I was about to program my nrf52840 with minor changes in the dts and after that I cannot flash any other images to the device. This is what I get when I flash the...
Hi~ I have a new NRF52833REV3 xxAA board, and I need to read its SRAM. However, when I use the JLink command to read it, I get 524288 bits 0. I have tried recover and erase...
Hello,
I am planning on using a 0201 15nH shielded inductor instead of the 0402-size listed on the schematic for the nRF52832.
Here's the link to the component: LMCI0201...
Hi Nordic,
We are now creating a BLE central device which can connect to an BLE peripheral device for some telemetry purpose.
To address privacy concern, the BLE peripheral...
Hello,
I have a workspace project that currently builds fine, however I am starting some new smaller projects and wish to build them as Freestanding so that I can have them...
Code snippet below produces the error code 0x00000001 during nrfx_spim_xfer:
The same SW in a different project does not produce the error. The error occurs during attempted...
Hello,
I have a project of a device with 2 endpoint plus the GP endpoint (242). It's a coordinator.
at first startup, the green power endpoint doesn't appear in the response...
Dear Nordic,
I'm trying to use the LTE Link Monitor and the Trace Collector V2 at the same time in order to collect trace messages from an nRF9160 DK. However, the RAW and...
Hello all,
I am looking for a freelancer to work on a Matter project based on a nRF52840 SoC.
I am an embedded developer and I did already some experiments with the Nordic...
Pretty new to development, compiled and flashed Zephyr basic samples through nrf Connect for VS Code (board type: nrf52840dk_nrf52840) and suddenly board wouldn't respond...
Hello Team Nordic,
We know that %XSYSTEMMODE command is used to set specific LTE mode. I am also using CONFIG_LTE_NETWORK_USE_FALLBACK.
I have a SIM card which connects...
--
I am using Laird's bl654 dongle. If you download a hex file using nrfConnect for Desktop, the dongle is no longer recognized. It works like open bootloader again only...
