We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I use the PPK2 to measure the power supplied from a lithium polymer battery to a test device. I use 'Ampere meter' and the 'Enable Power Output' switch in the UI then 'start...
Hello,
I am using SoftDevice S140 SDK 7.2.0. I need to initialize the no init parameters.
For doing that I used nrf_power_resetreas_get() return parameter. Two questions...
Hi,
The memory space of the application core for nRF9160 is empty.
Now,if I set the ERASEPROTCET register located in the UICR to 0( Erase protect will be enabled.), how...
I have a few issues/suggestions for improvement of the VSCode extension for Nrf Connect, that I like to submit to the developers : I tried the github link https://github.com...
Hi
In my firmware, i setup a NUS service, piece of code as below:
I found that the nus_send_enabled_cb function is always invoked before connected function...
Hi,
We're really stumped on this one. We recently deployed 150 devices running nRF SDK for Mesh. All except three of these devices are running a modified SimpleOnOff Server...
Hi,
I have problems to use nrf52840 dongle with Manjaro and nrf Programmer v3.0.3. Indeed, when I plug my dongle I have this view on programmer :
So I see only the numbers...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140. The 52840 board as ble central and an android app as virtual NUS peripheral...
I am working on adding a new LWM2M object (3302 Presence) to the lwm2m client project from SDK version 1.9.1. After creating and including the file "Kconfig.ipso_presence_sensor...
Hi,
I tried building and debugging the sample "https_client" using the method described here . But debugging fails. Debugging stops prematurely because the source file cannot...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
