We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
We found that when testing the nRF52832 chip, if the C9 capacitor is empty, the chip broadcast power consumption increases from 20uA to 40uA, and the power consumption of...
Hello,
Over the years we've occasionally been experiencing a issue with nRF52840 and nRF52832 chips in case of which any BLE activity would stop happening. A chip mounted...
Hi,
I've used the module https://github.com/NordicSemiconductor/cloud-firmware-ci-device-helpers-js to create device certificates for a nRF9160 device and then AWS JITP...
Hi there,
Is it at all possible to run nRF Connect for Desktop apps like the programmer and the power profiler from outside the nrf connect for desktop app?
e.g. is there...
Good day,
is there a way to check if a client is connected to GATT server/service? Would like to send a data after device gets reconnected.
i am using PCA10040 with...
Hello dear Nordic. I am wondering if I can simulate a hardware event by the software by writing any value to the event register, or in other words to create artificial interrupt...
Hi,
I implement the CLI on my nRF52820 and I see in function cursor_next_line_move in file nrf_cli.c they use "\n" but for my project I don't want to pass in cursor_next_line_move...
Hello,
I'm tryng to update nRF9160sip (rev b1), I push sw4 on power on and I see "MCUBOOT" device on "Programmer v3.03"
Then I select file "mfw_nrf9160_1.3.2.zip" and...
Hi,
I have made my own customboard with the nrf52811. For development I have used nrf52840dk.
I´m trying to program following:
I did solder one PCB by hand. It didn...
Hi Team,
I am looking for a new readily available to test on my Nordic board 52X version.
could you please share the inputs and the source code that i can test and upload...
Hello, is there a guide on what should be done to make the sample codes for the nrf52840_dk compatible with the nrf52840_dongle? If there isnt, can I please know how one can...
Hi,
we would like to set the USBD_SERIAL according to the device serial, which will be an abbreviated version of the MAC address. I've checked the code and can only find...
Hi,
I am getting a similar error. I have nRF52832 board connected to raspberry pi for flashing and debugging using openocd. As soon as openocd command is executed I start...
Hi guys. When reading the OOB pairing example,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_nfc_pairing/README.html
" This...
Hope someone can bring some clarification to me.
I am studying the principle of Shock-burst and a part of that study is to go through every step in the examples of “esb_low_power_ptx_pca10056...
