Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Hello Team,
I am using ble_peripheral application to establish ble communication with android. But, for some android devices the application automatically disconnects after...
The spec describes the App and Network keys as 16 byte hex strings and states that they are generated by a Provisioner.
Can you please clarify what algorithm is used to...
Hi everyone, I'm Eitan, 4th year electrical engineer student. I'm starting my specialization courses in communications and computers (embedded).
For my final project I want...
Hello, support team.
Now my colleagues are working on the software part for the hardware alpha version of the device with 2 independent antennas for LTE and GNSS. But the...
Hi,
Now I'm using :nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056\s140\arm5_no_packs.
And I want to add 'Characteristic User Description Descriptor...
Hello,
I'm build my application using v1.9.1 and Visual Code. It seems I have an error saying my application size is greater than the flash size.
I CANNOT jettison any...
I have a big issue about WDT during FDA 510K preparing. I have to proof that WDT of nRF52832 is seperated structurally from main system. since nRF52832 have such a seperated...
To whom it may concern,
I have a project (using Zephyr) where I need to switch UART pins while runtime. Is there a way I can handle this? This is how I initialize pinctrl...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
Hello,
I have a question regarding the advertising and scaning mechanism implemented in Zephyr.
To be more precise, suppose the node's radio is in scan mode, and it's...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
