Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I have 2 custom boards running as BLE central/peripheral.
The peripheral is running the beacon broadcast example from SDK 17, ble_app_beacon.
The central is running custom...
I'm working with an custom application and a bootloader with code drawn from the examples in SDK 15.2.0. The main method of my bootloader is below:
I can run and debug...
Hi Community,
I want to use the UART Logging backend in my bootloader. Whenever I want to start the actual application via nrf_bootloader_app_start(), the bootloader hangs...
"S132 Link Layer subset for SD 8.0.0" and "S132 Host Layer subset for SD 8.0.0" have been listed as component tested. The S132 v7.2.0 is available for download with the latest...
I have a thingy91 that has been flashed over JLINK which has wiped out the MCUBoot. I'm attempting to get it back using mcumgr. I have mcumgr all setup, but when I run
...
While stating debugging mode or normal mode i didn't pair with any devices after advertise duration in RTT viewer
This error raising [ 00> <error> app: Fatal error ]
and...
Hello Nordic community,
We are a software development team. We can directly work on development kits but as a initiative we are trying to buy SOC and do others steps manually...
As described in the brief spec of nRF 21540：
the nRF21540 improves the RX sensitivity by 5 dBm to -100 dBm.
5dBm should be 5dB，you can't make a simple plus/minus equation...
Hi,
I'm doing a Bluetooth test for the nrf52840. However, RF-PHY/TRM-LE/CA/BV-13-C cannot be tested. This means that the instrument does not provide results. The measuring...
Hello,
I want to supply the nRF52832 with a power supply of 2.2Vdc. The uC has to measure an analog voltage between 0 to 2.5V using the internal reference.
Is it possible...
I am trying to set up usb cdc and use the virtual COM port for logging. Please find my code below.
Issue - The LED part of the code works fine but when dongle is connected...
Hi,
I'm testing a prototype with the nRF52840 where I drive a buzzer in the following way:
When I play a signal, I see that the current through the buzzer is about...
Dear everyone,
I'm new to Zigbee and Nordic development. I'm currently working on Zigbee on nrf52833. I must implement a mesh topology to prove self-healing and self-routing...
Hello Nordic team,
I'm looking for some help about Thread creation ... I try to start a Thread when my nrf52840 receive a particular message. This message is sent with BLE...
