At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising. Since there is no example of "pure" extended advertising...
Hi Nordic team,
I am working on a project with one central and several peripheral BLE devices. The peripherals are moving randomly, is it possible to detect the event...
Hi, recently testing nrf9160 SMS example, but seems not working in both Send/Receive
I confirm that SMS is valid in my SIM Card, I put it in my mobile phone and verified...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
hello , I am working spi with softdevice(i.e., bluetooth). here spi master is nrf52 and spi slave is ad9837. the spi interface code works fine without soft device(i.e.,ble...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi,
I am trying to compile the cfb sample as provided in v2.0.0.
my overlay file is as follows
and my prj file
When I try to build, I get the following error...
is there a way to change the target device to nRF52820 (PCA10100) in segger embedded studio? initially configured to nRF52832 when we started our setup (nRF Connect Desktop...
I want to design a general module. Is it feasible to design the schematic diagram in this way?
1.VDDH is powered by external power supply, is that ok?
2.VBUS is powered...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
This is in reference to: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader
On step B1, it says: " Next step, inside SDKFolder\external\micro...
Hi,
I'm working on a project where the NRF52840 chip is connected to multiple peripherals (4 of them) through SPI. The hardware has been designed in a way that each peripheral...
Hi, I am using the ant_plus/ant_bpwr/bpwr_rx code as a reference to capture power data from an SRM power meter. I am at the point where I get the following messages, which...
Title says most of it. I'm wanting to perform an OTA DFU of an nRF52840 running NCS 2.0.0 using my android from either the nRF Connect Device Manager or nRF DFU app. There...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
