We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I am using the Sparkfun thing plus nrf9160 feather with SDK 2.0.0 and modem firmware 1.3.2. Ultimately I would like to get LTE working along with GNSS, however, I can't even...
Good morning.
I am looking for an example of how to program the u-blox NINA-B221 module using the AT commands so that it is compatible with the application of the Nordic...
I've just updated from nRF Connect v1.9.1 to V2.0.0. In my bluetooth code that worked in the older version, I setup a couple of callbacks for BLE pairing:
In v2.0.0, I...
Hi, We are developing with the nrf9160dk as our development board. We are working from the aws-nrf-cloud a-gps sample (cat tracker sample) for our stack as our main system...
I'm trying to work out why this happens, but am not a great expert at linker scripts. Currently, we use arm-none-eabi to build our projects (and cmake) to great effect. I...
Hello,
we are using the following equipment:
- nrf5340-DK Board
-Zephyr SDK 1.9.0
Our application is intended to transfer a large number of data over BLE.
So, we...
I would like to test nRF52832 passkey method with pc-ble-driver-py ( https://github.com/NordicSemiconductor/pc-ble-driver-py) . Does pc-ble-driver-py supports passkey? Where...
Hi, I am developing an application that includes the following features: 1. PWM to control the buzzer 2. 2 Uarte to communicate with 2 external devices 3. BLE to wireless...
I am trying to speed up the burning process.
I am using JLink ULTRA+ (swd max speed 50Mhz) and Jlink base( swd max speed 30Mhz) and NRF52833 but still get almost the same...
Hello,
We developed a system that consists of 1 central and 10 peripherals, all are based on nRF52840. Below is the configuration of the system:
Central: AWSFreeRTOS...
So I've been reading and re-reading all the guides and white papers for the last week, and I think I almost have my head wrapped around everything, but am struggling with...
I have a code build on top of nrfx 2.0 and after a few received bytes I get NRFX_ERROR_INTERNAL back from nrfx_uarte_rx call in blocking mode.
So I can process around 20...
Hello, I want to get information list about BLE GATT services and characteristics of a device.
I want to connect to a peripheral with a specific name, then get all metadata...
