Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
I'm using a nRF52832 for a product under FAA regulations. The standard requires the BLE module to perform a self-test. What self-test capabilities does the Nordic nRF52 family...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
Hello there,
I am using the rtc2 in NRF52832 to interrupt at randomly generated time instances. Now, I am trying to integrate this functionality in a framework that uses...
I would like to use the low power pwm library to get a breathing LED effect on my device. The MCU I am using is a BMD 350 and the LED is connected to nRF52 port P0.02.
...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
