At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello everyone, Right now I am working on a demo showing some functionalities of 2 smartwatches: Colmi P8B and PineTime. I am using nRF52840 for that purpose. I had the idea...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Hello,
In one of our application we are using the nRF52832. It communicates through I2C with three components:
- MAX32664
- MAX17201
- MCP4018T
We often receive...
I've created a new sandbox project for a nRF9160DK that requires a SPI Master for testing a Flash part. Since I already have "working" SPIM code in a different Segger project...
I am using the beacon mod example with my nRF52-DK to calc battery life. All measurements are taken with PPK2 (a great tool by the way), but in the PC application my timestamp...
Is there a process in place for updating a controller only build via the HCI? My current set up is a 9160 as the BLE Host, a 52820 as the BLE controller, MCUs are connected...
Hello, Im a little confused about the nRF Connect SDK ecosystem.
Currently Im using SES with cloned nRF SDK 15.0.3 for nrf52811, however I would like to start using https...
Hi
I plan to enable hardware flow control in the coprocessor code. After successful compilation and burning, I will use Ubuntu to start wpantund and an error will be reported...
We already made working code with NRF5 SDK. It has added three characteristics to send data via UART from a MCU. Each characteristics for separate purposes, for eg. Characteristics1...
Hello,
I'm selecting crystals for a project with nRF52832QFAA.
I noticed that on the spec the drive levels of HFXO and LFXO are 100uW and 1uW respectively. Should the...
Hi,
I'm trying to integrate https://github.com/nrfconnect/sdk-nrf in version v1.9.1 in my baremetal application (nRF5340 NET and APP CPUs). Where can I find the startup...
Hi,
we are using an nRF52833 for an application where we have a sensors, a USB interface and an SD memory device.
We would like to write and read back sensor values to...
Hi,
I am following the step by step tutorial " Getting Started with Secure DFU Bootloader Step by Step guide "
Before following the above guide I compiled ble_app_blinky...
Hello,
I'm trying to use the VL53L1X Time of Flight sensor on my nRF52DK, but I experience some problems.
Previously, I've successfully used the VL53L1X with an Arduino...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
