At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
There is a serial interface in the nRF SDK that makes it easy to serialize mesh data over serial
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am want to read Analog value from LDR sensor. I am unable to find ADC Input pin in nrf52840 Dongle datasheet but I got it in nrf52840 chip datasheet (page -576...
Hello Devzone Community,
I have a question set regarding correct, best way or ways to configure nRF9160 GPIOs for high impedance. My hardware is a custom board but shares...
I have the nrfConnect task that builds my project in vscode.
I need to add a script to execute before the nrfConnect task.
I added a task to my tasks.json but the task...
Hi,
Could you please tell me which firmware is flashed onto the thingy91 by default (both for the nrf52840 and for the nrf9160) ? Where can I find the source code for these...
Hello,
We are experiencing a strange issue when quickly turning off/on the NRF52840 on our board. In order to check whether the MCU wakes up correctly, a test fw was set...
Hi all,
If a client has only one root certificate, the servers that clients can connect to are limited. I want to provision multiple root certificates first and use them...
Hi,
I am using the MX25R64 NOR Flash chip on my own PCB with the nRF9160 package. With the help of this thread I have managed to get the NVS library to work with it. I...
hello all:
I'm using nRF52820, SDK 17.1.0, S113.
I made a BLE perpheral role, and it has two service, each service has two characteristic. like this:
When using nRF...
How do I remove nRF Connect SDK from Windows before re-installing?
And are there something that needs to be done, if you have used cmake and Visual Studio Code for other...
Hi,
I want to use in my project the saadc (I'm using segger embedded studio). So, I found that I have to add the driver file to the driver folder, and I have added the file...
im using nrf52840
with sdk 17
and segger ide
i recently discovered that the max count buffer is 16 bits meaning it has a limit of 65k bytes. im trying to receive 100k...
Hi @Torbjorn!
Hope you are doing good!
I tried using nrf52840/nrf52833 ble_app_blinky_c and ble_app_blinky for connectable coded PHY . But it only works for 1M_Phy . Although...
Hi there,
Our current understanding is that when building an application using NCS, the images of of MCUBoot and the application gets merged into merged.hex.
We however...
I'm a relative novice to linker files, just enough to be dangerous, but I have a need to understand what the Segger linker is doing. I have some success using `flash_placement...
