We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
nRF Connect SDK v1.6.1
HW - nRF 52832 DK
Host OS - Ubuntu 18.04 LTS
SES IDE Nordic Edition v5.60 with Segger J-Link USB
If I build the Peripheral UART example then...
Hi ,
I had done the user guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/ug_matter_configuring.html#ug-matter-configuring , could you please tell...
Somehow it seems the interface MCU of my PCA10040 DK got confused. I cannot use the JLINK to the nRF any more, and the JLINK drive (in Windows 10) does not show up. LD5 stays...
Hi,
1. I want to know the minimum delay time of BLE data transmission
2.How should this time be calculated
Thank you for all your assistance. Kind regards, Peter.Mi...
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello Nordic Devzone,
I am currently attempting to generate 8mhz clock output to a gpio pin on the nrf5340dk. I have found previous posts about utilizing the gpiote, timer...
Dear Members,
How can I find the cause of
<error> app: Fatal error ?
I can't see an error code ?
Is it possible hardware error because voltage surge ? Can capacitor...
When I set NRF_LOG_ENABLED true, the RTT log can be output without any problem, however, the scanning or advertising activity stop immediately.
I found there is something...
Hi,
I am trying to find Get and set the RTC timer api inside Nordic SDK "nCS\v1.6.1\zephyr".
Could you please help me where I can get these api.
Thank You!!
I got up to this stage while trying to evaluate the module...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk_gsg%2FUG%2Fnrf91_DK_gsg%2Fintro.html
There...
Several place refer us to the SoftDevice Release Notes; eg
https://www.nordicsemi.com/eng/nordic/Products/nRF52832/S132-SD-v5/58987
http://infocenter.nordicsemi.com/topic...
Hi,
I have nRF52840 DK with nRFConnect SDK 1.6.99
Compiled and run on nRF52840 boards:
F:\_Develop\ConnectSDK\ncs\zephyr\samples\bluetooth\periodic_adv
F:\_Develop...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
What does m_ble_observer stand for ? i don't see any explanation in the whole project...
According to the Overview of this sample, the sample supports the provisioning of the IoT device using "Azure IoT Hub Device Provisioning Service (DPS)" to an IoT hub; and...
