Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
Hello,
After some weeks of inactivity and moving my desk to an other address, the nRF connect application is not running and show a white screen for all applications except...
Just checking in, I am recently starting to develop cellular communication and looking to develop on the nRF9160. I have been in nRF52 space and with that I develop inside...
Hi, I'm using nrf52840 DK. In my project I want to receive audio from microphone (analog) and stream it to bluetooth headphones. Is there any possible way to do it? Any help...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
hello!
im using sdk 17.0.2 with softdevice s112 in our customized board as i want to work for long range mode,so i need extended advertisement ie no available in s112 so...
