Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
i have a custom board with an nrf52840, i use a J-link programmer to flash the chip with the nrf connector programmer app.
I am able to read the memory and erase the chip...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.5.1
Zephyr version: 2.4.99
BLE controller...
Hi,
I want to run the Thread MQTT-SN Publisher and Subscriber example using the nrf52840 DK and the nrf52840 Dongle I have on hand.
I was able to sucessfully build and...
Hi, I'm trying to use BLE/Thread Multiprotocol for BLE RSSI scanning and send values using Thread, is it possible to use BLE and Thread(FTD) concurrently with out time-slice...
Hi all, Using SDK 17.0.2, on a Laird BL653. I've been messing with creating variable PWM sequences and found an issue where a 100%->0% duty cycle transition does not occur...
I once used nRF Sniffer with my nRF51822 module. I see that everything has updated since - Wireshark, Sniffer plugin (now is Python 3.4+), Sniffer firmware. As I can see,...
Hi all, i don't have any issues I am just now using the nRF Connect power profiler after a ~4 month break. WOW, the major update is absolutely phenomenal. The graph is very...
Dear Nordic DevZone community,
we modified the LwM2M client example to fit our application in a LTE-M network. Now we are trying to get GPS to work while still being able...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
