We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all,
I am trying to do bonded buttonless DFU but an error named NRF_ERROR_FORBIDDEN was raised in enter_bootloader() function under ble_dfu_bonded.c.
The description...
hi，
I currently have an application scenario，using a nRF52832(M board) BLE maser to upgrade another nRF52832(S board) is run standard DFU ，Are there any demo available？
Previously, I used SEGGER to build and run programs on nRF52 DK very quickly (5-20 seconds).
However, for nRF5340 DK, it usually takes about 8-15 min to build and run just...
Hi,
I am trying to connect the current product with MCU EFM32GG290F1024 to a Nordic BLE module in a serialization over UART.
I have port the SDK to my project and need...
1. hardware : nRf52840 dongle.
2. Purpose : Update Firmware into dongle to be sniffer, and restore original default manufacturer firmware for nRF Connect v2.6.0 desktop...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
Hello.
We are using NRF52840, SDK 16.0.0 and SoftDevice S140 7.3.0 and are noticing irregular SoftDevice asserts that don't seem to be triggered by any one particular function...
Hello,
I am curious to see if it is possible to register a device through a web app using the nRF52840's NFC. The goal is to scan the NFC on the device, enter the personal...
Hello,
I'm working on a custom board with a nRF52833.
A small external battery is on the board, and when the power is off, 32.768khz of low power remains on the battery...
I'm running the SDK 17 radio test example on two nRF52840 DKs. My goal is to do a PER measurement in 802.15.4 -mode.
I configure the boards to use ieee802154_250Kbit mode...
Hi, I am using nrf52832 board. I was trying to disable the GPIOTE interrupt for a particular event (Event4) using INTENCLR register. My code was NRF_GPIOTE->INTENCLR = 1 ...
I am trying to get the nRF9160 DK power consumption down as much as possible to establish a baseline for development. After struggling to achieve the values claimed in the...
