Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I have just acquired a new nRF52 DK devkit.
Performing a `nrfjprog --recover` followed by `nrfjprog --eraseall` doesn't work to remove the protection.
I do not flash...
Hi,
I use the secure BLE Bootloader to update the nRF52840 (with S140).
Now I want to add a UARTE to update the STM32 connected to nRF52.
Do you have a solution to do...
Hello,
I am using two nrf52840 DKs to test ble transmission and i2s output. The nRF Connect SDK I use is v2.6.0.
Both of them are ble connected. One sends data to the...
Hello,
I think llpm's sample project is wrong. Evaluation board is not supposed to be communicating.
To verify the defect, the value of the time variable is fixed. This...
hello, my code was built under ncs v2.6.0 and tool chain 2.6.0 without issue, I upgrade them to v2.9.0, then I get these errors, can not figure out how to fix them.
could...
Hi,
From https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/direct_test_mode/README.html , it writes " After programming the sample to your development...
Hi,
I’m working on enabling the asynchronous API on UART1 in the nRF Cloud Multi-Service sample for the nRF9151. Despite setting the necessary configurations, when I call...
I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
NCS 2.7 with mcuboot via sysbuild
custom board with nrf52840, 2 custom applications (manufacturig and end-user)
In my application our DFU will be performed over BLE...
Hi,
I have the following Device Tree in my application:
I get the error -134 during the application startup. Debugging the application shows that the error happens...
Hi, I'm developing ble applications.
But there are problems on calling Ble APIs.
If I call the functions that conatins bt_le_adv_start() in main loop(Maybe main thread...
Hi,
I have a BLE interface with services and characteristics and I want to have different level accesses for my characteristics with for example two levels:
level user...
Hi,
Setup:
nRF NCS 1.9.x and nRF NCS 2.5.0
nRF5340 and nRF52840 both with an external crystal attached to HF clock input.
Problem:
Inaccuracy in timing of UART at...
This is sort of a hardware question, involving the RADIO peripheral in the nrf52(840) line. The question is simple. Is there any limitation on when you can change the TXPOWER...
I have a driver for a Piezo buzzer running on bare metal that I would like to port to the nRF connect SDK. The existing PWM-based driver in Zephyr does not fulfill my requirements...
