Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I have a NRF52840 device connected by BLE to another NRF52840 BLE USB dongle connected throw USB to a PC application.
I want to synchronize the RTC on the connected...
Hello I am currently working on a project with the XM122 / XB122 kit for an evaluation, the XM122 card integrates an nrf52840 MCU and a radar sensor;
The goal of my project...
Hi, I'm using nrf52833 with SDK 17.0.0.
I want to send SAADC data over BLE.
So, I want to see data in my phone.
I've modified codes.
I want to use macro(ble_nus_data_code...
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
Hi
I am looking to make this example work but this post is old...
Hi all,
we are now using nRF52811 and its SAADC. We would like to use the oversampling functionality, but there is some information missing in the datasheet.
So, when...
Hello,
nRF5SDk16.0, Softdevice v.7.0.1, device nRF52840.
We using manufacturer specific information in the advertisement data. Here are the set values:
The data is...
We have a PCB production with bug where AC13 (P0.18) accidently has a via shortenede to GND plane on internal layer. Thus nRESET is stuck low and cannot be pulled high without...
Hi,
I modified the LBS service to experiment sending more than a byte of data.
On the peripheral side, modified from ble_peripheral/ble_app_blinky
typedef struct { uint8_t...
I'm using visual code for my development. I've tested a basic hello world app, this works fine so c/cpp is correctly installed.
I'm now testing a basic app, but I'm getting...
Hi Team,
For our development we are using the nRF52840 soc, We need the some example code or some project which will explains the Usage of RSA algorithm and supported API...
Hello,
I am looking at the ble_app_buttonless_dfu/main.c
This implementation is initializing the queued write module. Is this required now for DFU operation? We currently...
Hello,
For some reason whenever I try to pip install pc-ble-driver it will only ever install version 0.11.4. This causes a problem since I need the nrfutil library and the...
I sent some nRF9160 prototypes down to a CTIA certified test lab in North Carolina to do carrier TRP and TIS testing. When they add their test sims they seem to be unable...
Dear Sir,
I am new in embedded.
I start work on nrf9160.
I have to acquisition periodically through mqtt protocol, a data, with total space of approximately 30 kb, and...
