Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
We want to qualify a product with nrf52832 and preferable S132 6.1.1. When we tried to use QDID 125047 there were inconsistency problems in Launch Studio, table 1a was not...
Can i configure more than one pin for wake up the microcontroler from deep sleep ? like this: nrf_gpio_cfg_sense_input(30, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_LOW); nrf_gpio_cfg_sense_input...
What is the receive buffer size for IP packet data, i.e. how many bytes of data can the modem receive (in one or several UDP packets) before I call recv() or recvfrom() on...
Hi Sir,
For test the nRF9160 GPS, based on the nRF connect v1.2.0.
Do we have the GPS API for cold/warm/hot start?
And which example code we can reference?
Thank you...
Hi,
Recently I have been working on serial LTE modem code and it seems to work great for TCP and UDP. I am trying to enable GPS module by the command mentioned in this link...
Hi,
is the 100k pull-down on the COEX2 pin required as stated in the product specification ? I don't see it being followed anywhere (reference circuitry, nRF9160 DK schematic...
Hi,
I am developing nrf52832 on zephyr platform, I have seen a very useful GitHub library you guys have created called 'NordicPlayground' https://github.com/NordicPlayground...
How can I log on a router when a coordinator is in pairing mode, what I mean is that the coordinator sends a message so the routers know and set them selfs up on pairing mode...
For our nRF52832-QFAA design, we've just completed all tests according EN 300 328 (Radio). All but one test passed: spurious emissions at 4.9 GHz showed -44dBm, exceeding...
I use nRF52832 chip and SDK 15.3 version. I try to build nRF52 project with SDK 15.3.0. I spent a lot of time to fix a lot of issue in during compilation and linking. I used...
Hello,
I'm trying to build the HTS221 sensor example for nRF9160 but got this error :
I'm compiling the code with ncs v1.2.0 and here is my prj.conf :
Can someone...
Now I can only download the 《nRF52810 product brief.pdf》 . The link is shown below:
https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52810/GetStarted...
Hi,
I am using nRF52832 for my project. I want to perform secure connection using numeric comparison.
I want to know how six digit passkey is generated by the softdevice...
Hi,
For the testing purpose, I would like to send a few basic packets from LTE Link Monitor on nRF9160 DK to our cloud. I found a way how to do it through the nRF9160: Serial...
Hello guys,
We are developing our IoT prototype with Thingy:91 board using v1.2.0 tag.
One of the things we need to to is as follows:
Scan the BLE area looking for...
