I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Summary
With CONFIG_OPENTHREAD_BORDER_ROUTING=y (the default selected by CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y ) and CONFIG_OPENTHREAD_TREL=y (also the default), the...
I'd like to know more about the single-antenna AUX functionality of the nRF9151. More specifically, this line in the documentation for AUX has piqued my interest:
When the...
Hello,
I am attempting to develop an open source nRF52832 PCB design, aiming to minimize the footprint as much as possible.
Thus, I attempted to cramp as many components...
I had one nRF54l15-DK,and I want to make a music player by nRF54l15's BLE,but I am not sure is it supposted LE audio to client my headphone.if it supposted, is it full LE...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
Hello,
I am working with the nRF9151 DK and NCS v3.3.0 . I am experiencing a critical modem fault at startup.
Problem Summary: When I start debugging, I immediately get...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
