Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
SDK version: 15.3
Soft-device version: 6.1.1
Hi,
I've been working on a low power application where every 10's of uA is important. My application requires SPI as...
Can you provide documentation of the energy costs for creating/verifying ed25519 and NIST P-256 signatures with the CryptoCell CC310 peripheral found on the nRF52840 device...
I am trying to set pins when I press a button, and clear is as soon as I stop pressing the button, however the board turns on all leds at once and does not respond to input...
I came across this old thread, which asks the same question, but was abandoned by the OP ( ) without follow-up:
https://devzone.nordicsemi.com/f/nordic-q-a/26699/52832-saadc...
Hello,
I am looking into migrating DFU and Bootloader over BLE from SDK v15.0 to SDK v15.3. I have a few questions about the code changes which I was hoping I could get...
I was reading about Mesh DFU and noticed that when it happens, the receiving node will rebroadcast it to all devices within radio range. It seems like devices will pick up...
Hello all,
I am trying to adjust the current consumption of my device based on nrf51822 s130.
A have read the https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines...
I wrote some user data to 3rd party nrf52840 boards flash using the command "nrfjprog --memwr 0x1001084 --val 0x33333333" , when I ran the program the data values was not...
Hello,
I want to test the mesh provisioning demo with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
I have encountered...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
