I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi everyone,
I have a custom board with a nrf52832 and a I2C device connected to P0.21 (SCL) and P0.20(SDA). I was trying out the twi_scanner example and had modified the...
Hello,
Is there someone who has worked recently with nRF52840 and SHT21 (Humidity / Temperature) sensor ? I have to do some basic test for HW and validate that sensor...
Hi, i would like to work with nrf52832 for my IoT idea. So my question is where do i start from to work with this particular SOC nrf52832 chip? My End product would have integrated...
Dear Madam/Sir,
I'm trying to compile the ble_proximity example on SEGGER Embedded Studio with SDK 12.3.0 and SoftDevice 2.0.1 to run on nRF51822 with PCA10001.
After...
Hey,
I have implemented the ble_hid_mouse example in the nRF52832, and implemented both central multilink and USBD in the nRF52840 dongle so that both boards are paired...
Hi,
We are using nRF52840 in our product for both Client and Server communication on BLE5. We are seeing an overall average time of 5+ seconds for the overall connect, data...
Hello everyone!
I have started to work with openthread recently, and now I have to build a mqttsn client into a stm32 uController. I'm doing that by using the spinel protocol...
Does the nrf52832 has some delay when the shortcut of END_START is enabeled in continuous receiving?What is the meaning of rx chain delay?Does RX chain delay in 2Msps mode...
I'm having problems getting the peer manager to work in a project forked from the ble_app_template on my nRF52-DK (using pca10040e, S112), complaining it can't initialize...
Hi, I am using ble_app_uart_saadc_timer_driven example, which work just fine when receiving data on smartphone (using nRF Connect app). Now I would also like to do the same...
Hi,
I'm using the Nrf52810 with softdevice S112 for the moment.
Question 1:
In ble_gap.h i see that there is a define BLE_GAP_WHITELIST_ADDR_MAX_COUNT (8). Is this realy...
Hi,
I am reading a voltage value from an analog sensor which changes values with 0.02V step. So, i need the accuracy up to 0.02V from ADC channels . But right now i am...
Hi,
I have project based on nRF52840 (using SDK 15.2) and I have a problem with properly adding ADC measurement using scheduler - description as below.
Problem description...
Hi
I want to create this example:
A major network,it include the subnet A and subnet B.
One node X,it belong to subnet A and subnet B.
If the node X was a function...
